All entries for March 2022

First irradiation studies of RSBs at the Dalton Facility

Writing about web page https://www.dalton.manchester.ac.uk/research/facilities/cumbria-facilities/

Last week was a first in the field of Radiation Dense Materials in that samples of Reactive Sintered Borides (RSBs) and cemented Tungsten Carbide (cWC) were irradiated for the first time by proton beam and gamma irradiation at the Dalton Cumbrian Facility in the Westlakes Science Park during some truly beautiful springtime weather.

Much work on simulating the radiation response and attenuating properties of a cWC, cWC-RSB and tungsten boride shielding concepts has occured during the 2010s onward [C.G. Windsor et al 2015 Nucl. Fusion 55 023014,C.G. Windsor et al 2018 Nucl. Fusion 58 076014], however, data on the radiation response of cWCs [Shielding materials in the compact spherical tokamak https://doi.org/10.1098/rsta.2017.0443] is very sparse due to their recent adoption as candidate shielding materials. No data on radiation response exists for RSBs due to their novelty so this will be the first time any practical data will be obtained from irradiated RSB materials.

The planned experimental work at DCF fell into two main topics: Proton irradiation and gamma irradiation. Each type of radiation would take place at two different intensities and at two different temperatures.

Proton radiation most closely resembles the conditions at or near the plasma-facing component of a tokamak reactor and hence was to take place at ambient and at 600^oC.

Gamma radiation will be significant at all parts of a tokamak reactor but particularly near the superconducting magnets. These irradiations were performed at -196^oC (77K) and at ambient. Each experiment consisted of three samples: cWC, RSB and W metal alloy with eight different irradiation conditions with a 9th sample set to sit in the gamma irradiator for long-term irradiation studies.

So....how did the work go and what happened over last week? Read on.

The gamma irradiation mostly went to plan. Low dose gamma irradiation was set to 30 kGy for both the 77K and ambient irradiation. High dose gamma radiation samples was set to 240 kGY for ambient and 90 kGY for 77k. The lower dose at 77K is a result of the different sample positioning due to the dewar and the requirement to change the N₂ the dewar every 5 kGy to prevent excessive ozone formation, which is an explosion hazard. All gamma irradiated samples except the long-term samples have been returned.

Proton irradiation was less straightforward. The high dose ambient proton irradiation was successful, with a steady state temperature of 125^oC and a total dose equivalent to 1.66 x 10¹⁸ protons. Subsequent proton irradiation attempts were unsuccesful, mostly due to the plasma failing the strike and therefore enable the proton beam to irradiate the samples. However, these sample will be irradiated this week and sent by post.

This is one of the many hazards of experimental work in that failure is always an option but nevertheless this work on completion will provide an important first step in realizing the cWC-RSB concept as practical radiation shielding materials whatever the damage or lack of is present on analysis.

This work would not be possible without the dedication of the staff and researchers at the DCF who make this possible.

Jessica Marshall : 30 Mar 2022 15:27 |  Tags: Dcf Gamma Radiation Irradiation Nnuf Proton Rsb Tungsten Carbide |  Comments (0) |  Close comments |  Report a problem

The Inaugural Entry – the life and times of the Radiation Dense Materials Group

Writing about web page https://warwick.ac.uk/fac/sci/physics/research/condensedmatt/radiation_dense_materials

Welcome to the Radiation Dense Materials Group Blog. This blog will showcase the latest research from this group alongside how the research came to be with notes and photos of facilities, locations and conference trips. This will give people an insight into how research takes place on a day-by-day basis and on how many steps it takes to get to where you want to be.

The Radiation Dense Materials group aims to sythesize, study and develop novel concept radiation dense materials with the initial aim of making compact radiation shielding for fusion reactors and to make practical fusion power generation possible by 2030. It is envisaged that this will only be one such application for radiation dense materials when considering the need to expand the nuclear sector as a carbon-free power source.

Nuclear fusion has the potential to be a safe, effective carbon-free power source but has been limited in part by the lack of materials that can both attenuate radiation effectively and withstand the extremes of temperature expected within a power-generating fusion reactor. The plasma-facing component is expected to withstand temperatures up to 1000^oC during normal operation. Superconducting magnets require cryogenic cooling (<77K), both of which would be seperated from each other by the shielding/coolant/Tritium blanket by little more than 1-2 m in a compact spherical tokamak. The initial cWC-RSB concept aims to be able to satisfy both radiation shielding and mechanical aspects with respect to this application.

This blog aims to be as interactive as possible and to give people an insight into how scientific research takes place behind the scenes.

Jessica Marshall : 30 Mar 2022 13:40 |  Tags: Condensed Matter Fusion Power Physics Tungsten Carbide Warwick |  Comments (0) |  Close comments |  Report a problem